Celebrating 35 years

Need a quote?  Click here >

 
Convergent Technologies
Industrial Sounder/Strobe AmberProduct Code: RD-RSS01A

Primarily designed for noisy environments where
normal loud ringing is drowned or is
difficult to hear. The unit gives excellent
"bounce around" from the strobe
light. Easy to install - mount on wall,
plug into power outlet and then plug into
Telephone Line.
During incoming ring, the unit produces
a sound and also flashes a strobe light.
The sound type is adjustable across 32
settings using internal adjustments.
Suitable for direct Telephone Lines and
Analog Phone ports or PABX Systems.

Features

  • Fly Lead with BT Plug Supplied as Standard
  • 22Vdc - 240Vac Power Adaptor Included
  • Wall Mountable
  • Amber or (optional Clear, Blue, Green, Red available)
  • 2 Part Unit
  • Strobe Output
  • Sound Output - 1 of 32 Tones
  • Volume Control
  • Very High Light Output
  • Telephone Cord - 2 metres
  • 22Vdc plug pack

 

IQ333SRDRSSO-1A Instructions 

 

IQ333SRDRSSO-1A Tone Chart


ES2-FL Telephone Ringer Unit 2 WireProduct Code: 8486000
ES2-FL Telephone Ringer Unit 2 Wire

Features

  • Line Powered
  • Adjustable Volume
  • 1 of 4 Tones Preselectable
  • Wall Mountable
  • Can also be used on 24 to 48Vdc when optionally wired.
  • NZ and Aust. Approved

Specifications:

  • 90dBA Nominal at 1 metre
  • Can also be wired to operate on 24 to 50Vdc

Bedlam Weatherproof Loud RingerProduct Code: 8471900
Bedlam Weatherproof Loud Ringer

Features

  • Telephone line powered (no mains voltage required)
  • Greatly reduced installation costs
  • Penetrating output (105dBA typical)
  • Volume control
  • Available for hard wiring (screw or I.D.C.) or with 3 metre line cord
  • IP66 Rated
  • REN of 1.5
  • Maintenance free operation


Specification:

  • Approved for New Zealand and Australia

1825 Duet plus with 240Vac plug packProduct Code: 1825P
1825 Duet plus with 240Vac plug pack

Features

  • Adjustable Warble Generator Built-in
  • Full Range of Tone Adjustment
  • Volume Control
  • Telecom Line Input Trigger
  • Low Voltage AC/DC Input
  • Audio Input
  • Clean Relay Contact Input
  • Interface to other External Devices


Specification:

  • Frequency: 80Hz to 20kHz
  • Sensitivity: 89dB +/-2dB at 1.0W, 0.5m (600Hz)
  • Audio output: 3.5Wrms continuous in to 8 ohms
  • Volume Control
  • Power adapter: DC 22~24Vdc, 350mA (Included)

Telerelay Ring Detect Relay Product Code: RD-RLY01
Telerelay Ring Detect Relay

Features

  • Telephone Ringing Voltage Detection with Relay and FET programmable outputs
  • Message Waiting Detection - Voltage Detection on PABX systems only
  • Relay and FET Reverse Role
  • Power Supply Included
  • 12 to 48Vdc Operation and Switching
  • Easy Wiring


Specifications:

  • 12 to 48Vdc Operation
  • 12 to 48Vdc <1A Resistive Load on either output
  • Use to Drive your own External Devices
  • Slave Relays available for larger loads
  • Built-in 10sec Time Delay if required
  • Built-in PABX Message Waiting Detect if required
  • Power FET Output for Sounder or Light/Strobe Options
  • Relay Output for Light or Strobe Options
  • Can have Strobe Continuous Power Drive State during ringing cycles and sounder Ringing with the Ring Cadence at the same time
  • Relay can follow ringing cadence or HOLD between ring cycles
  • Power FET can follow ringing cadence or HOLD between ring cycles (must have Relay HOLD as well to work otherwise follows Relay)
  • POTS or PABX Hold between ring cycle period selectable
  • Relay can be disconnected via a LINK so as only FET can switch giving totally silent switching for Radio Station Hotlines etc. ie. no relay clicking on Microphone in Studio
  • With the PABX Message Waiting Facility it can be used in Call Centres and Hotels etc. for an easy solution to advise supervisor and others that calls are being missed. Adjustable 65Vdc to 100Vdc simultaneous to Ringing Detection. Therefore, for practical reasons can only be used for one or the other

IQ333SRD-RLY01 Installation Guide